Yamashita lost
The
Variety of answers: 9383 | Number of accepted: 6
2015-12-0918: 59: 19
U disk can not uncover the really hard disk immediately after startup
1. Just after inserting the U disk, boot into the BIOS to modify the settings, verify no matter if it really is denied towards the U disk, or directly boot according to the F9 or F10, F11 motherboard. The diverse settings will be the boot sequence settings, and after that make use of the old Maotao or Chen Maple U disk begins, doesn't enter the PE interface, straight enters the GHOST technique Daquan interface, then starts GHOST11, the other can't commence, or there's a dilemma, then load the image, directly GHOST.
2. Boot into the PE interface, check irrespective of whether you are able to see your difficult disk, and after that copy the XP image straight to the neighborhood difficult disk, then from the boot, use the U disk to enter the DOS interface, manually start off GHOST, load and restore. SD Card accidentally deleted Video recovery software to modify SATA mode
1. Just after getting into the BIOS, enter the 'Config' web page
2. https://en.wikipedia.org/wiki/Sd_card -enter the 'SerialATA (SATA)' page
three. Modify the original 'AHCI' to 'Compatibility] or [IDE]
Case study: How to set the SATA in the BIOS of your HP laptop to IDE mode
Just after booting into the motherboard BIOS, set SATA to Compatibility or IDEMode within the BIOS. The HP notebook BIOS enters F10. As for the BIOS version, the setting place is different, but the setting strategy is usually to set SATA to compatible mode or ID mode. You could also try and change the installation disk with a SATA difficult drive, or press F6 in the beginning with the installation to install the driver. Just after the installation, you are able to set up it commonly. In case you use XP to install,
A blue screen appears or just immediately after getting into the installation interface, it prompts that 100% is the problem of SATA mode setting if the tough disk can't be discovered, enter the BIOS settings, or obtain a reasonably new ghost version of XP installation,
Typically, the new version on the ghost method is straight compatible with SATA mode, which can be usually not the case with VISTA, except for IBM X200 machines. At this time, just transform AModeSelection → adjust 'AHCI' to 'IDE' → press 'F10' to save and restart.
The problem that the tough disk cannot be discovered when the U disk is began is primarily triggered by the SATA mode. Within the SATA mode, the startup on the U disk is restricted. The user can only use it ordinarily if the SATA mode is changed towards the IDE mode.
Comments 0
amazing
0
Baishui Hillbilly
The
Variety of answers: 21196 | Number of accepted: 3
2015-12-0919: 37: 18
1. Immediately after inserting the U disk, boot in to the BIOS to modify the settings, check no matter whether it is denied to the U disk, or directly boot based on the F9 or F10, F11 motherboard. The various settings would be the boot sequence settings, and after that use the old Maotao or Chen Maple U disk begins, does not enter the PE interface, straight enters the GHOST program Daquan interface, and after that starts GHOST11, the other can not start off, or there's a problem, then load the image, straight GHOST.
2. Boot into the PE interface, check no matter whether you can see your very own really hard disk, after which copy the XP image directly to the neighborhood really hard disk, then restart, make use of the U disk to enter the DOS interface, manually begin GHOST, load and restore. Just enter the BIOS and alter the SATA mode.
Hope to assist you!
Comments 0
great
0
Geek is Mang
The
Variety of answers: 16476 | Number of accepted: six
2015-12-0921: 05: 27
Hello, you can refer to the following option methods: 1. Press the F2 important to enter the BIOS any time you 1st boot (Note: Because the hotkeys for entering the BIOS of various brands of computer systems are unique, please be sure you press the corresponding hot as outlined by the motherboard model Crucial to enter the BIOS), after entering the BIOS, press the arrow keys around the keyboard to pick Config, and press the Enter crucial to enter the Config page.
two. Just after entering the Config page, enter the SerialATA (SATA) web page utilizing the arrow keys, press Enter to enter, and after that transform the original AHCI to IDE. Immediately after you press Enter, the alterations are total.
three. Press F10 to save right after the alter is completed, press ESC to exit the BIOS, or press ESC to exit the BIOS directly, and pick YES just after prompting irrespective of whether to save.
Right after the alter is full, it is possible to restart to enter the PE method. Right after entering the PE technique, you will see drive C, drive D, drive E, and drive F.
Note: If the difficult disk nevertheless can't be displayed by the above technique, it might be that the hard disk is burned out and you can only replace the hard disk.
I hope useful to you!
Comments 0
awesome
0
Comments